改性丝瓜络纤维对水体日落黄的吸附特性

采用化学改性的方法将丝瓜络制备为阴离子吸附剂,并将其用于水体日落黄(SY)染料的吸附,分别考察了吸附剂的用量、日落黄染料的初始浓度(C0)、p H值、温度(K)、时间(T)5个因素对吸附效果的影响。通过模拟吸附等温曲线、吸附动力学以及热力学方程并通过比表面积(BET)和红外光谱(FTIR)分析改性丝瓜络吸附染料前后和丝瓜络改性前后的变化情况以此探究其吸附机理。结果表明,p H对吸附效果影响不明显;最大吸附量随温度升高而增大,在298 K温度时最大吸附量达到137 mg/g,是未改性丝瓜络的9.78倍。Langmuir方程拟合吸附过程描述最好,吸附类别为化学吸附。吸附过程符合伪二级动力学,是一个自发和吸热的过程。改性丝瓜络可以有效去除水体中的日落黄染料。     

二氧化钛脱除高温烟气中的氯化氢

HCl是城市垃圾焚烧产生的主要气体污染物之一。将一种新型脱氯剂TiO2引入到垃圾焚烧系统中,并与其他脱氯剂的性能进行比较。研究了不同脱氯剂使用量、不同反应温度和不同HCl气体浓度对TiO2、CaO和CaTiO3脱氯效果的影响。结果显示,TiO2能在高温(800~1 000℃)、高HCl浓度(1 303.6~1 629.5 mg/m3)下获得较好的脱氯效果。与传统的脱氯剂CaO相比,TiO2更适合于高温烟气脱氯,其在1 000℃时的氯容(36.3 mg HCl/g TiO2)几乎是相同情况下的CaO氯容(9.3 mg HCl/g CaO)的4倍。而CaTiO3的脱氯效果不但受到自身分解效率的影响,还受到TiO2和CaO脱氯效果的影响,其脱氯效果较差。     

Ultrasound pretreatment of filamentous algal biomass for enhanced biogas production

The filamentous alga Hydrodictyon reticulatum harvested from a bench-scale wastewater treatment pond was used to evaluate biogas production after ultrasound pretreatment. The effects of ultrasound pretreatment at a range of 10–5000 J/mL were tested with harvested H. reticulatum. Cell disruption by ultrasound was successful and showed a higher degree of disintegration at a higher applied energy. The range of 10–5000 J/mL ultrasound was able to disintegrated H. reticulatum and the soluble COD was increased from 250 mg/L to 1000 mg/L at 2500 J/mL. The disintegrated algal biomass was digested for biogas production in batch experiments. Both cumulative gas generation and volatile solids reduction data were obtained during the digestion. Cell disintegration due to ultrasound pretreatment increased the specific biogas production and degradation rates. Using the ultrasound approach, the specific methane production at a dose of 40 J/mL increased up to 384 mL/g-VS fed that was 2.3 times higher than the untreated sample. For disintegrated samples, the volatile solids reduction was greater with increased energy input, and the degradation increased slightly to 67% at a dose of 50 J/mL. The results also indicate that disintegration of the algal cells is the essential step for efficient anaerobic digestion of algal biomass.     

Current status and historical variations of phthalate ester (PAE) contamination in the sediments from a large Chinese lake (Lake Chaohu)

The residual levels of phthalate esters (PAEs) in the surface and two core sediments from Lake Chaohu were measured with a gas chromatograph–mass spectrometer (GC–MS). The temporal–spatial distributions, compositions of PAEs, and their effecting factors were investigated. The results indicated that di-n-butyl phthalate (DnBP), diisobutyl phthalate (DIBP), and di(2-ethylhexyl) phthalate (DEHP) were three dominant PAE components in both the surface and core sediments. The residual level of total detected PAEs (∑PAEs) in the surface sediments (2.146?±?2.255 μg/g dw) was lower than that in the western core sediments (10.615?±?9.733 μg/g) and in the eastern core sediments (5.109?±?4.741 μg/g). The average content of ∑PAEs in the surface sediments from the inflow rivers (4.128?±?1.738 μg/g dw) was an order of magnitude higher than those from the lake (0.323?±?0.093 μg/g dw), and there were similar PAE compositions between the lake and inflow rivers. This finding means that there were important effects of PAE input from the inflow rivers on the compositions and distributions of PAEs in the surface sediments. An increasing trend was found for the residual levels of ΣPAEs, DnBP, and DIBP from the bottom to the surface in both the western and eastern core sediments. Increasing PAE usage with the population growth, urbanization, and industrial and agricultural development in Lake Chaohu watershed would result in the increasing production of PAEs and their resulting presence in the sediments. The significant positive relationships were also found between the PAE contents and the percentage of sand particles, as well as TOC contents in the sediment cores.     

Structural regulation of electroplating sludge by a metal–organic framework synthesis method for an enhanced denitrification activity

Journal of Material Cycles and Waste Management - Electroplating sludge contained multi-metals and organics. In previous reports, electroplating sludges were usually recycled by direct calcination...     

Cadmium (Cd) distribution and contamination in Chinese paddy soils on national scale

Rice is a staple food by an increasing number of people in China. As more issues have arisen in China due to rice contaminated by cadmium (Cd), Cd contamination in arable soils has become a severe problem. In China, many studies have examined Cd contamination in arable soils on a national scale, but little studies have focused on the distribution of Cd in paddy fields. This study explored the spatial pattern of Cd in paddy soils in China, made a preliminary evaluation of the potential risk, and identified the most critically contaminated regions based on the domestic rough rice trade flow. The results showed that Cd concentrations in paddy soils in China ranged from 0.01 to 5.50 mg/kg, with a median value of 0.23 mg/kg. On average, the highest Cd concentrations were in Hunan (0.73 mg/kg), Guangxi (0.70 mg/kg), and Sichuan (0.46 mg/kg) provinces. Cd concentrations in paddy soils in central and western regions were higher than those in eastern regions, especially the southeastern coastal regions. Of the administrative regions, Cd standard exceedance rate was 33.2 %, and the heavy pollution rate was 8.6 %. Regarding to Cd of paddy soil, soil environmental quality was better in Northeast China Plain than in Yangtze River Basin and southeastern coastal region. Mining activities were the main anthropogenic pollution source of Cd in Chinese paddy soil. Based on rice trade, more of the Chinese population would be exposed to Cd through intake of rice produced in Hunan province. Certain regions that output rice, especially Hunan province, should be given priority in the management and control of Cd contamination in paddy soil.     

Pollution characteristics of 23 veterinary antibiotics in livestock manure and manure-amended soils in Jiangsu province,China

The aim of this study was to investigate the pollution characteristics of typical veterinary antibiotics in manure and soil of livestock farms in Jiangsu province. This investigation employed solid-phase extraction (SPE) coupled with ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). A total of 53 manure and 50 amended soil samples from 16 livestock farms in Jiangsu province were collected for analysis. In the manure samples, the highest detected frequencies and concentrations were those of tetracyclines (TCs, 54.1 ± 5775.6 μgkg^?1), followed by fluoroquinolones (FQs, 8.4 ± 435.6 μgkg^?1), sulphonamides (SAs, 3.2 ± 5.2 μgkg^?1) and macrolides (MACs, 0.4 ± 110.5 μgkg^?1). Statistical analysis was used to illuminate the pollution characteristics of 23 veterinary antibiotics for various animal types and different regions in Jiangsu province. The results showed that the pollution level in cow manure was relatively lower compared with pig and chicken manure due to the relative restriction of medication. Furthermore, contamination was serious in amended soil from chicken farms. The pollution level in manure among different regions was higher to the south and north compared with the centre of the region. The same outcome was found for soil. Antibiotic residues in organic fertilizer were also investigated in this study. We found that although the detected concentration was lower in organic fertilizer than in fresh manure, detection frequencies (10–90%) were high, especially for roxithromycin (90%) in MACs (30–90%). This finding suggests attention should be paid to the pollution levels in organic fertilizer. This study is the first extensive investigation of the occurrence and distribution of many kinds of typical veterinary antibiotics in manure and soil from livestock farms of Jiangsu province. This investigation systematically assesses veterinary antibiotics usage and related emissions in southeast China.     

Chemical compositions and sources of atmospheric PM10 in heating, non-heating and sand periods at a coal-based city in northeastern China

Mass concentrations and chemical components (18 elements, 9 ions, organic carbon [OC] and elemental carbon [EC]) in atmospheric PM(10) were measured at five sites in Fushun during heating, non-heating and sand periods in 2006-2007. PM(10) mass concentrations varied from 62.0 to 226.3 μg m(-3), with 21% of the total samples' mass concentrations exceeding the Chinese national secondary standard value of 150 μg m(-3), mainly concentrated in heating and sand periods. Crustal elements, trace elements, water-soluble ions, OC and EC represented 20-47%, 2-9%, 13-34%, 15-34% and 13-25% of the particulate matter mass concentrations, respectively. OC and crustal elements exhibited the highest mass percentages, at 27-34% and 30-47% during heating and sand period. Local agricultural residuals burning may contribute to EC and ion concentrations, as shown by ion temporal variation and OC and EC correlation analysis. Heavy metals (Cr, Ni, Zn, Cu and Mn) from coal combustion and industrial processes should be paid attention to in heating and sand periods. The anion/cation ratios exhibited their highest values for the background site with the influence of stationary sources on its upper wind direction during the sand period. Secondary organic carbon were 1.6-21.7, 1.5-23.0, 0.4-17.0, 0.2-33.0 and 0.2-21.1 μg m(-3), accounting for 20-77%, 44-88%, 4-77%, 8-69% and 4-73% of OC for the five sampling sites ZQ, DZ, XH, WH and SK, respectively. From the temporal and spatial variation analysis of major species, coal combustion, agricultural residual burning and industrial emission including dust re-suspended from raw material storage piles were important sources for atmospheric PM(10) in Fushun at heating, non-heating and sand periods, respectively. It was confirmed by principal component analysis that coal combustion, vehicle emission, industrial activities, soil dust, cement and construction dust and biomass burning were the main sources for PM(10) in this coal-based city.     

废弃SCR脱硝催化剂的再生及其脱硝性能研究

对废弃脱硝催化剂处理后重新加工再生,研究了添加剂对其粉体成型和再生催化剂脱硝活性的影响,探讨了反应温度、空速、n(NH3)∶n(NO)摩尔比、氧含量、H2O和SO2对再生催化剂NH3选择性催化还原(SCR)NO的影响。结果表明:最佳再生条件是使用5%羧甲基纤维素和10%无机粘结剂辅助成型;废弃催化剂再生利用率高达90%;再生催化剂抗压强度为4.73 MPa,优于商用催化剂;空速5 000 h-1、氨氮摩尔比1、氧含量6%时,脱硝活性温度窗口为310⁴50℃,350℃时活性最高为94%;350℃时,单独通入1 000×10-6SO2或10%H2O对再生催化剂活性均有一定抑制作用,最低活性分别为70%和81%,停止通入SO2或H2O后其活性逐渐恢复;同时通入1 000×10-6SO2和10%H2O,再生催化剂活性下降至63%并于1 h内保持相对稳定,停止通入SO2和H2O 2 h后,活性逐渐恢复到73%。